Search Results

The 2GIG 345MHz Repeater is designed to work with 2GIG security systems providing more flexibility in where wireless sensors can be installed. The 2GIG Repeater can be installed in the optimal location to extend the range of 2GIG panels for large jobs. The 2GIG 345MHz Repeater will repeat 2GIG and Honeywell sensor signals to 2GIG panels. The Repeater is a plug and play device that will immediately start repeating signals when powered on. The rechargeable battery provides backup power in case of AC power loss.

The Alarm Controls AM3300 is a 1/2” spacer plate designed for the 600 series magnetic lock. The unit lowers the magentic lock by 1/2” and has a clear anodized aluminum finish.

The AVR-NT816A from Avycon is a 16 channels 4K UHD digital video recorder, no HDD.

The GEM-PIR is an advanced PIR sensor designed for use with Napco’s GEM-Series wireless receivers. The unit is powered by two 3-volt lithium batteries (supplied) for long service life. When battery voltage drops below normal, a low-battery report will be sent to the receiver (replace with Duracell DL123A or Varta/ Power-One CR123A only). Coding switches are not used in the GEM-PIR. Each transmitter has a unique factory-programmed RF ID code (printed on the unit) that distinguishes itself to the receiver. (Note: See control-panel instructions for entering this six digit hexadecimal code and checksum digit into the panel; be sure to enter all numbers and/or letters, including leading zeros, if any).

Includes: 7” All In One Touchscreen, 8-Core SOM, PowerG or SRF, Simultaneous LTE & Wi-fi Dual Path Communication, Bluetooth 4.2, Z-Wave 800 Series, Bluetooth Music Streaming, Microphone for Live Video/Live Answer, Single 4W Speaker + 85dB Siren, SmartMount Installation System with optional Desk Stand.

The Alula Door Window Sensor is a full-featured security transmitter with industry-leading wireless range and battery life. It is typically used to sense opening and closing doors and windows, but can secure just about anything using its two external contact zones. It will alarm when the magnet is pulled away from the sensor or when an external contact is opened.

The ELK-M1XEP is an Ethernet Appliance with a RS-232 Serial Port Interface. It may be used to connect a control in the M1 Family to an Ethernet network. It features email event notification and FIPS compliant encryption algorithms for security sensitive environments. It is powered by an ELK-P1216 12 Volts DC, 1.5 Amp plug-in power supply/adapter. A software setup utility is built into ElkRP for configuring the connection setup, network password, etc. The M1 Ethernet Interface is factory defaulted to obtain a dynamic IP address from a DHCP server (i.e. router, cable modem, etc.). It may optionally be setup with a static IP address.

The PAD100-PSSA (Single Action) is activated by simply pulling the white “T” bar handle down. Once activated, the “T” bar cannot be reset without opening the front cover. Opening the front cover will also activate the pull station. To reset the PAD100-PS Series, use the Potter WS-93 key to unlock and open the front cover. Once the cover is open, push the “T” bar back into the normal position and re-secure the front cover.

The OSYSU is used to monitor the open position of an OS&Y (outside screw and yoke) type gate valve. This device is available in two models; the OSYSU-1, containing one set of SPDT (Form C) contacts and the OSYSU-2, containing two sets of SPDT (Form C) contacts. These switches mount conveniently to most OS&Y valves ranging in size from 2” to 12” (50mm to 300mm). They will mount on some valves as small as “ (12,5mm). The cover is held in place by two tamper resistant screws that require a special tool to remove. The tool is furnished with each device and should be left with the building owner or responsible party. Replacement or additional cover screws and hex keys are available.