Browse Categories

Search in Brand

SYSTEM SENSOR

Filter Your Search

Show Attribute Category Group

Shop by Category

Loading...

Search Results

Searching for: system-sensor
Viewing Page 1 of 8 (75 results)

SYSTEM SENSOR LED HORN/STOBE, 2-WIRE, INDOOR,WALL,RED

Item #: SYS-P2RLED

Supplier Part #: P2RLED

The System Sensor L-Series P2RLED 2-wire horn strobes are rich with features that increase application versatility, simplify installation, and maximize profits with lower current draw and modern aesthetics. LED lighting technology offers significantly lower current draw compared to older Xenon bulbs across a full candela range. This improves design flexibility for notification appliance circuits (NACs) while also reducing power supply requirements, allowing for simpler and lower-cost installations.
In addition, the System Sensor L-Series with LED notification appliances offer a new diagnostic test point feature that allows you to measure device voltage with a digital voltage meter (DVM) without removing the appliance from the wall or ceiling. The DVM test points are discreetly located on the face of the notification appliance, which enables faster troubleshooting and end-of-line (EOL) voltage checks while greatly reducing the risk of misplacing or damaging appliances during troubleshoo

IN STOCK

SYSTEM SENSOR LED HORN/STRB, 2-WIRE, INDOOR, CEILING

Item #: SYS-PC2WLED

Supplier Part #: PC2WLED

The System Sensor PC2WLED L-Series LED 2-wire horn strobes are rich with features that increase application versatility, simplify installation, and maximize profits with lower current draw and modern aesthetics. LED lighting technology offers significantly lower current draw compared to older Xenon bulbs across a full candela range. This improves design flexibility for notification appliance circuits (NACs) while also reducing power supply requirements, allowing for simpler and lower-cost installations.
All devices feature plug-in designs with minimal intrusion into the backbox, making installations fast and foolproof while virtually eliminating costly and time-consuming ground faults. In addition, the System Sensor L-Series with LED notification appliances offer a new diagnostic test point feature that allows you to measure device voltage with a digital voltage meter (DVM) without removing the appliance from the wall or ceiling.

IN STOCK

SYSTEM SENSOR LED HORN/STRB, 2-WIRE, INDOOR, CEILING

Item #: SYS-PC2RLED

Supplier Part #: PC2RLED

The System Sensor PC2RLED L-Series LED 2-wire horn strobes are rich with features that increase application versatility, simplify installation, and maximize profits with lower current draw and modern aesthetics. LED lighting technology offers significantly lower current draw compared to older Xenon bulbs across a full candela range. This improves design flexibility for notification appliance circuits (NACs) while also reducing power supply requirements, allowing for simpler and lower-cost installations.
All devices feature plug-in designs with minimal intrusion into the backbox, making installations fast and foolproof while virtually eliminating costly and time-consuming ground faults. In addition, the System Sensor L-Series with LED notification appliances offer a new diagnostic test point feature that allows you to measure device voltage with a digital voltage meter (DVM) without removing the appliance from the wall or ceiling.

IN STOCK

SYSTEM SENSOR LED HORN/STRB, 2-WIRE, INDOOR, WALL

Item #: SYS-P2WLED

Supplier Part #: P2WLED

The System Sensor L-Series P2WLED 2-wire horn strobes are rich with features that increase application versatility, simplify installation, and maximize profits with lower current draw and modern aesthetics. LED lighting technology offers significantly lower current draw compared to older Xenon bulbs across a full candela range. This improves design flexibility for notification appliance circuits (NACs) while also reducing power supply requirements, allowing for simpler and lower-cost installations.
In addition, the System Sensor L-Series with LED notification appliances offer a new diagnostic test point feature that allows you to measure device voltage with a digital voltage meter (DVM) without removing the appliance from the wall or ceiling. The DVM test points are discreetly located on the face of the notification appliance, which enables faster troubleshooting and end-of-line (EOL) voltage checks while greatly reducing the risk of misplacing or damaging appliances during troubleshoo

IN STOCK

SYSTEM SENSOR REMOTE TEST STATION W/KEY

Item #: SYS-RTS151KEY

Supplier Part #: RTS151KEY

The System Sensor RTS151KEY is an automatic fire detector accessory designed to test remotely located duct and beam detectors. For 4-wire detectors, the RTS151KEY features a multi-colored LED that alternates between steady green and red. Green indicates power and that the detector board is in place. Red indicates alarm. For 2-wire detectors, the LED will show red for alarm. Consult the detector installation instructions for additional information.

IN STOCK

SYSTEM SENSOR DUCT SAMPLING TUBE 5' WITH HOLES

Item #: SYS-DST5

Supplier Part #: DST5

The DST family of sampling tubes are pieces of steel piping with a series of holes drilled the entire length of the tube and should extend the entire width of the duct. The correct length has to be chosen for width of the duct where it will be installed. The sampling tube length must extend at least 5/8 across the duct width for optimal performance. The sampling tube is always installed with the air inlet holes facing into the air flow. The tubes lock securely into place and can be removed by releasing the front or rear locking tab.

IN STOCK

SYSTEM SENSOR DUCT SAMPLING TUBE 3' WITH HOLES

Item #: SYS-DST3

Supplier Part #: DST3

The DST family of sampling tubes are pieces of steel piping with a series of holes drilled the entire length of the tube and should extend the entire width of the duct. The correct length has to be chosen for width of the duct where it will be installed. The sampling tube length must extend at least 5/8 across the duct width for optimal performance. The sampling tube is always installed with the air inlet holes facing into the air flow. The tubes lock securely into place and can be removed by releasing the front or rear locking tab.

IN STOCK

SYSTEM SENSOR REMOTE TEST STATION W/SWITCH ALARM & PWR

Item #: SYS-RTS151

Supplier Part #: RTS151

Remote test stations are automatic fire detector accessories designed to test duct smoke detectors from a convenient location. For 4-wire detectors, the remote test station features a multi-colored LED that alternates between steady green and red. For 2-wire detectors, the LED illuminates red for alarm.

IN STOCK

SYSTEM SENSOR 6" FIRE BELL RED 24VDC

Item #: SYS-SSM246

Supplier Part #: SSM246

System Sensor® SSM Series alarm bells are low-current, high-decibel notification appliances for use in fire and burglary systems or other signaling applications. They come pre-wired to reduce installation time, and also incorporate a polarized electrical design for use with supervision circuitry. With reliable performance, SSM Series alarm bells provide loud, resonant tones. They operate on 24 VDC and are motor driven.

IN STOCK
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • NEXT »

The following web pages were found that match your search

Line Card 1/17/2025
Brands We Sell Brands you know and trust. See PDF Line Card More