Shop POTTER ELECTRIC SIGNAL CO. | Brands We Sell

The EBP-407C annunciator system is designed with a superior dual-counter, dual-active, infrared technology. The invisible infrared beam is designed to trigger a pleasant chime sound. The infrared signal differentiates among entry and exit. The dual entry/exit counter registers a count any time the beams are interrupted. Each event is counted, recorded, and registered by the built-in digital counter, and can be viewed and compared later in entry/exit modes.
Complete Kit Includes:
1 Infrared beam sensor with dual counters?1 Electronic chime with volume chime?1 Reflector?1 Power transformer (XF-1220 UL/CSA approved) 1 Long plastic bracket
1 Metal short bracket?2 Short plastic brackets?1 6 ft. power cord with in-line switch?1 26 ft. 4-conductor chime wire (AWG #24)?2 Screws for mounting chime?4 Screws for securing mounting brackets?1 3/8” bolt with locking washer to secure infrared beam sensor

With no specialist tools or knowledge needed for installation and operation, the Fireray One is a standalone beam smoke detector that prioritizes ease of installation.
Using the Fireray One, it couldn’t be easier to bring the benefits of beam smoke detection to your application:
Auto-AlignmentTM – just steer the laser onto the Reflector, then at the flick of a switch, it aligns itself. 8 times faster than previous detectors
One person installation – everything can be done by one person
One standalone product – no specialist tools required; minimal prior knowledge and training needed

The transmitter enclosure has a threaded nipple, O-ring and locking nut for mounting directly to the conduit entrance of any dry contact device not listed as explosion proof. The transmitter provides two flying leads for connection to the normally open contacts of any listed dry contact fire alarm device. The connection is supervised for opens and shorts using the supplied 5.1k ohm End Of Line Resistor. The transmitter does not latch, it follows the status of the sprinkler switch it is connected to. The unit is powered by two (2) AA size 1.5 volt Lithium Iron/Disulfide batteries. The device includes a cover tamper switch as well as an LED to indicate when the battery meter has been reset.

The MP Series is a standard THERMOFLEX® single circuit, Normally Open contacts detectors, in which the connectivity is modified with pigtail leads that extend through a seal plate.This provides for enhanced protection against corrosive or moisture-laden environments. This model is a fixed temperature only detector and should be installed in areas where rapid fluctuations in ceiling temperatures are expected.
This detector is suitable for use in areas where condensation or corrosion can have harmful effects on circuit wiring connected to standard terminals. Its seal plate (with extended pigtail leads) will mount onto a typical cast exterior back box.The detector is connected to a fire alarm system’s input circuit as an initiating device.The internal contacts are normally open, and will close when the detector operates either on a rate of temperature increase, or if the releasing temperature is reached.

The Isolator Base 6” (PAD300-IB) comes with an integrated isolator module included. The base has a locking feature for the detector that may be used or removed in the field. Once the head is removed, the isolator is accessible in the bottom of the unit.
The isolator will open the Signaling Line Circuit down stream when a short circuit is detected. This will provide devices between the control panel and the isolator to continue to operate. The short is indicated by a steady red LED and once the short is removed the unit will return to normal operation.

The Potter Pull Station Series offers a complete line of die-cast pull stations for a variety of applications focusing mainly on fire alarm systems. The pull stations are available in single or dual action models. All of the pull stations have a 10-amp snap action switch and a dedicated terminal block for the ease of wire connections. All of the metal is completely coated to inhibit corrosion and provide for a uniform and quality finish.
The standard models have a hex key reset, however a key reset is also available. The models are available with shallow and deep surface mount back boxes and as a weatherproof version.

The AMS-39 Series Standard Surface Mount Contact us a UL listed contact designed to protect a wide variety of openings such as: man doors, sliding doors, windows, cabinets, hatches, and many others. Includes screws, covers, and spacers, 5 sets per pack

The Potter Amseco SH-1224W white strobe/horn provides a wide range of candela light output options in a single device. The candela settings include a 12 or 24 volt DC operation for the 15, 35 and 60 (75 on axis) candela settings and 24 volt DC operation for the 15, 35, 60, 75, 95 and 110 candela settings. The candela setting is displayed through the front window and is selectable using a drum wheel.

The horn settings include Temporal, Non-Temporal, March Time and a Chime sound. The horn also has Low, Mid and High volume settings for each pattern and tone. The tones include 2400 Hz, ElectroMechanical, Broadband and Chime.

The AMS-37 Series Industrial Magnetic Contact is a UL Listed magnetic contact built for rugged environments and practically any opening. It is designed to provide clean and quick installations. The AMS-37 Series can be used to protect openings such as: man doors, overhead doors, roof hatches, or hinged skylights.