Shop Wireless

The SK-910RBQ series of wireless receivers meet the growing demand for receivers with multiple, independently-controlled output functions. These RF receivers are compatible with both code hopping and fixed code transmitters. The receivers can be used to remotely control a variety of home automation devices such as garage door openers, lights, motorized gates, lifts, or other devices.

Based on the Acuity® glassbreak detector
2 lithium batteries included
Tamper-activated test mode: should be tested using the AFT-100 glassbreak simulator

The Alula RE611P is a Connect+ encrypted, pet-immune, wireless indoor PIR motion detector with 90° detection range. The RE611P protects indoor areas and transmits an alarm when motion is sensed from up to 40 feet away or when the external contact is opened. The RE611P is battery powered and requires no installation tools.??The Alula indoor motion sensor provides real-time information when motion is detected. Versatile and long-lasting, the RE611P sensor is designed for both residential and commercial applications which enables protection for a wide range of installations. Protect residential installs without false alarms caused by pets. With adjustable sensitivity levels, this wireless PIR is designed to monitor for human movement while intelligently ignoring pets.

96 Zone wireless reciever module for Napco’s GEM-Series control panels.

The Wireless Touch Screen Keypad (2GIG-TS2-E) is a wall-mounted, full-color, touch screen interface that provides many of the same easy-to-use keypad functions available on the control panel. It is designed for indoor use only and gives users the ability to control lights, thermostats, and door locks, as well as to view the status of every sensor zone.
When the 900 MHz Transceiver Module (2GIG-XCVR2-345 / 2GIG-XCVR2E-345) is installed in the control panel, the system can be programmed to communicate with up to four (4) Wireless Touch Screen Keypads.

The GEM-PIR is an advanced PIR sensor designed for use with Napco’s GEM-Series wireless receivers. The unit is powered by two 3-volt lithium batteries (supplied) for long service life. When battery voltage drops below normal, a low-battery report will be sent to the receiver (replace with Duracell DL123A or Varta/ Power-One CR123A only). Coding switches are not used in the GEM-PIR. Each transmitter has a unique factory-programmed RF ID code (printed on the unit) that distinguishes itself to the receiver. (Note: See control-panel instructions for entering this six digit hexadecimal code and checksum digit into the panel; be sure to enter all numbers and/or letters, including leading zeros, if any).

The 2GIG 345MHz Repeater is designed to work with 2GIG security systems providing more flexibility in where wireless sensors can be installed. The 2GIG Repeater can be installed in the optimal location to extend the range of 2GIG panels for large jobs. The 2GIG 345MHz Repeater will repeat 2GIG and Honeywell sensor signals to 2GIG panels. The Repeater is a plug and play device that will immediately start repeating signals when powered on. The rechargeable battery provides backup power in case of AC power loss.

Be prepared for today’s thieves with SECO-LARM’s patented CODEBUMP technology. With CODEBUMP, so-called code-grabbers and scanners are rendered obsolete because the RF code changes every time the transmitter button is pressed. In addition, with over 18 quintillion (1.8×1019) codes, the chances of ever repeating a code are virtually non-existent. SECO-LARM’s ENFORCER CODEBUMP transmitters and receivers are perfect for controlling garage and gate openers, car and home alarms, plus much more.

The Alula RE629 is a Connect+ encrypted wireless glassbreak detector used to monitor against the sound of broken glass up to 20 feet away. The RE629 glassbreak detector has four sensitivity levels that you can adjusted, making it more flexible for each application. The RE629 glassbreak detector is compatible for sending alarm signals to the Alula Connect+ wireless security system. When sensor detects breaking glass, the LED will turn on for 5 seconds. The glassbreak detector also has low battery supervision and a cover tamper to increase the reliability that it will work when you need it. For quick and easy mounting of the sensor, the RE629 comes with included tape and anchors.

The Alula RE115 GE/ Interlogix Compatible Wireless CO Sensor provides alerts to dangerous levels of CO. Sensor provides CO level memory indication, and an end of life notification. The alarm will signal when a dangerous amount of CO is detected.